reset mass air flow sensor chevy silverado

Step 4 Clean your dirty mass air sensor. This will be simalar with a 4.

Never Do This When Cleaning Your Mass Air Flow Sensor Youtube Car Repair Diy Car Mechanic Car Maintenance

Remove the screws that hold the mass airflow sensor in place.

. Simply spray the inside of the sensor let the cleaner sit for a few seconds and wipe off any excess cleaner on the inner and outer edges. Vehicle Stuck in Limp Mode Problems How to reset. Chevy Mass Air Flow MAF Sensor Replacement Guide.

Pull the air inlet hose off the sensor and then pull the sensor off of the air filter housing. After the engine cools down you can go to the mass air flow sensor location and remove the connector from the sensors harness. Unplug the electrical connector from the mass airflow sensor.

Now well proceed to the very delicate cleaning of the flow meter. GMC Savana Van and Chevy Express Van 43L 53L 60L Engines 2003-2008. In the service or maintenance options you should have the option to reset the MAF sensor settings.

The most direct way to do it is to use a scan tool to access the ECU via the OBDII interface. Driving your Silverado 1500 with a bad MAF sensor can damage the engine so you must act urgently to avoid more expensive repairs. It should be considered a high priority to fix as the MAF sensor not reading properly can really make an impact on the performance of the vehicle.

In this video i show you how to clean or replace mass airflow sensor chevy silverado tahoe suburban. The two most common trouble codes in relation to the MAF sensor are. 2004 Chevrolet Silverado 1500 Crew Cab.

This is great because it helps you narrow down the problem. Gmc sierra yukon denali. On this episode of Fear No Fix Jim and Chris replace the Mass Airflow Sensor MAF in a 53L Chevrolet Silverado model years 1999-2006Need help diagnosi.

2006 Chevy Silverado wiring diagram 593. The mass air flow sensor is part of the engines intake system. Now use the airflow cleaner to spray the plate and clean them.

Reset Mass Air Flow Sensor Chevy Silverado. After removing the mass airflow sensor make sure not to touch or damage any sensor elements. 2000 chevy venture van 3 Reprogrammed factory The MAF mass air flow sensor is a sensor mounted in a vehicles.

Locate the mass airflow sensor near the engine air filter housing. Heres a general guide on how to do it. Step 2 Remove the MAF sensor.

I have 2007 silverado 1500 5 chevy 1500. With the Chevy Silverado P0101 means the the Mass Air Flow MAF sensor has a RangePerformance problem. Restart engine and let it idle for at least 5 seconds.

This is very important if you have just used the car. Press the red clip slightly to unlock it. You dont reset the sensor you reset the ECU that is monitoring the MAF.

Start engine and warm it up to normal operating temperature. Use a flat head screwdriver to loosen the hose clamp screws. There are other codes related to the mass air flow sensor as well but these are the most common ones.

If you dont have any contact cleaner on hand using WD-40 or another. The mass air flow sensor or MAF sensor is part of the intake system in Chevy Silverado 1500 responsible for measuring the amount of air entering the engine. P0420 P0430 p1351 on 97 Chevy Silverado 57L I have read the article on this topic.

Next spray a small amount of contact cleaner into the electrical connector. You now have to take the MAF out to clean it. In this video i show you How to Clean or Replace Mass Airflow Sensor Chevy Silverado Tahoe suburban.

Tighten the screws so that they are snug. Disconnect mass air flow sensor harness connector. How To Test The GM Mass Air Flow Sensor.

Browse Categories Answer Questions. Chevy Silverado P0101 Diagnosis. Do not spray too much and spray twice or thrice at a time.

Turn ignition switch OFF. Let soak the lower part of your mass air flow sensor not the plug part in acetone or another solvent for a few minutes which will take out most of the grime. The intent of this cleaning will be to take out all its impure substances to enable it to work efficiently again.

First to cool your cars engine down you need to turn it off. 1999-2006 V8 Chevrolet Silverado GMC Sierra. However you should be careful to not scrub the parts as this might end up breaking or damaging the wire.

You dont reset the sensor you reset the ECU that is monitoring the MAF. Silverado mass air flow sensor my truck is throwing code 101 mass air flow i have already changed out the mass air - Chevrolet 2004 Silverado 1500 Crew Cab question. Answer 1 of 2.

Stop engine and reconnect mass air flow sensor harness connector. Now in case this is not the article youre looking for there are also 3 other GM MAF sensor test articles. The most common signs of bad mass air flow sensor MAF in Chevy Silverado 2500 HD are loss of power or slow acceleration engine hesitation or jerking during acceleration erratic idling misfires poor exhaust emission values and sometimes black smoke comes out of the tailpipe.

Now take out your Mass airflow sensor cleaner and spray it inside of the sensor. First locate the MAF sensor. There are two hose clamps on each side of the MAF sensor that hold it in place.

Furthermore detach the connection between the electric connector. Idling The Engine. It will be near the intake manifold or throttle body and it will likely have a large electrical connector going to it.

There are two hose clamps on each side of the MAF sensor that hold it in place. As for the mass air flow sensor looking at technical service bulletins there is one. Mass air flow sensor AFH50M-04 25 Boyce pic hide this posting restore restore this posting.

We will cover exactly what that means and potential fixes for it below. 3 symptoms of a faulty mass air flow sensor. Then let the cleaner sit for few seconds.

Install the new MAF on your Chevrolet. MAF Sensor Circuit Low. Make sure you dry the MAF sensor before fitting it back to the car in the air duct.

Pin On Jean Michel